Installation

Download printable PDF Guide

T-air towel bars have only been tested in walls with a solid support behind them, such as; brick / block walls, solid wood and any walls with a wooden ‘stud’ or ‘noggin’ support behind the plaster wall, or tiled wall. It is only recommended that they be installed in a similar wall with sufficient support i.e. not plaster only wall.

For towel bars being used for bath towels it is recommended that typically the hangers be mounted at 1800mm – 1850mm from floor, as this accommodates all standard towels along with bath sheets.

If bath sheets are not being used, then any height >= 1400mm will accommodate a standard towel. Heights of 1400mm – 1450mm are suitable for most children to use the hangers.

All T-air models are designed so that the eyelets are pointing down and inwards, just like the eyelets in the T-air Logo. The towels will automatically gravity fall into this pointy end of the eyelet, thus no need to force the towel into the eyelet. Some models have the screw holes above the T-bar, whilst others have the screw holes below the T-bar. Most important is to have the eyelets pointing in the same direction as per the logo, no matter what model you are installing.

It is very important that the holes drilled (for the screws), should be the correct size to allow the screw thread to bite and make a secure fit, otherwise the screws will loosen over time. When screwing into wood, the holes must be smaller than screw thread. The supplied plug for inserting in brick/block/concrete walls provides a suitable size for the screw to bite.


[halves]

Supplied:

  • 1 * T-air product
  • 2 * 42mm stainless steel screws
  • 2 * green wall plug/anchors (for brick/block walls)
[halves-break]

What you need for installation:

  • Stud finder
  • Level
  • Pen
  • Painters tape (for tiled wall)
  • Power drill
  • Drill bit (carbide or diamond tip if tiled wall)
  • Screwdriver (Phillips head)
  • All relevant safety items e.g. safety glasses
[/halves]

Step 1

Hold the hanger at the required height and location. Use Level to check that straight and level. Use pen to mark the wall where both the screw holes are located.

[gallery][/gallery]

Step 2

Where you marked the wall, drill 2 holes through wall into wooden ‘stud’ or ‘noggin’, ensuring the drill is held square and level.

If the wall is tiled, it is recommended to use painters tape where you have marked your drill holes to reduce the risk of damaging the tile when drilling. A glass and tile drill bit should be used (typically carbide or diamond tip). Once the drill has penetrated through tiles, it is recommended to replace with a general purpose drill bit to continue drilling screw pilot hole into the wooden ‘stud’ or ‘noggin’. This drill bit should be smaller than the hole drilled through the tile and smaller than the screw thread, to ensure the screw bites strongly into the support wood ensuring a secure hold.

If the wall is brick / block, it is important to insert the supplied green plugs as an anchor for the screws to hold onto. This will require a larger hole to be drilled into the wall (typically 6 - 6.5mm hole) to fit the plug.

[gallery] [/gallery]

Step 3

Insert the screw by initially using a Phillips head screwdriver, to locate and ensure the screw is square. Continue with either the screwdriver or power drill with a small drill extension, to ensure no damage from the drill chuck occurs on the hanger. It is recommended to do final tightening of the screws with the screwdriver to ensure that the screw is not over-tightened and that the head is flush or below the surface of the backing plate so that the cover plate fits squarely over backing plate.

[gallery] [/gallery]

Step 4

Clean the backing plate and screws to ensure that the cover plate sticks firmly to the backing plate. Peel the top layer of the double-sided tape (which is stuck on the back of the supplied cover plate) and place / stick this cover plate over the backing plate / screws. The cover plate is designed so that the small hole is located on the edge closest to the T-bar bend.

[gallery] [/gallery]

Caring for your Product:

Cleaning of all T-air products must only involve the use of a soft cotton cloth with water and if needed a mild detergent such as a typical dishwashing liquid. Absolutely no guarantee or warranty will be considered if our products are exposed to cloths with rough surface, sharp objects or harsh chemicals.

You are now ready to suspend your towel in air